An application-oriented structure, low moments of inertia, compact dimensions and a high degree of intrinsic operational reliability characterise these robust and dynamic motors.
The compact design and the low moment of inertia allow these motors to be used in dynamic applications. If your application calls for a broad speed setting range and a robust construction, then the choice is easy: MCA asynchronous servo motors from Lenze.
Whether as a self-ventilated version or with a blower - with a power range from 0.8 to 53.8 kW, the MCA asynchronous servo motors offer rated torque values of up to 280 Nm and peak torque values of up to 1100 Nm. In comparison to standard three-phase AC motors, these servo motors have the edge in terms of lower moments of inertia, lower weight and higher maximum speeds.
If you are looking for Lenze MCA Asynchronous Servo Motor, please call us at (800) 894-0412 or email us at firstname.lastname@example.org we will do our best to help you find the Lenze MCA Asynchronous servo motors that you are looking for at the most competitive prices possible. If you are searching for Lenze MCA Asynchronous servo motor technical information (data-sheets) please use the datasheets or product selection guide page links.
- High dynamic performance thanks to low moments of inertia
- Compact size with high power density
- Robust regenerative resolver system - alternatively SinCos and incremental encoder for the highest precision
- Easy to install and service friendly thanks to use of SpeedTec connectors
- Terminal box optional up to MCA21 MCA22 and 26 with three-part terminal box
- Protection: IP23, IP54, IP65 optional for naturally ventilated servo motors
- cURus-approved, GOST-certified, CE, RoHS-compliant
- High maximum speeds
- Wide speed setting range
- Field weakening operation usable
- Electronic nameplate
With asynchronous servo motors, two characteristics are shown in each case. The characteristics for continuous operation (S1) show the speed-dependent constant torque of the motor when operating with a servo inverter that itself is operated at a constant switching frequency. The limit torque characteristics correspond to those that come about during operation of the motor with the largest possible 9400 Servo Drive in each case. The servo inverter is set to a variable switching frequency here.
The asynchronous servo motors MCA10 to 19 and 21 can be fitted with integral permanent magnet holding brakes. In the case of permanent magnet brakes, the rated torque applies solely as holding torque at standstill. This is due to the nature of their design. During braking from full motor speed, e.g. in the event of emergency stops, the braking torque is significantly reduced. As such, they may not be used as safety elements (particularly with lifting axes) without additional measures being implemented. The brakes are activated when the supply voltage is disconnected (closed-circuit principle). When using the brakes purely as holding brakes, virtually no wear occurs on the friction surfaces.
If no suitable voltage (incorrect value, incorrect polarity) is applied to the brake, the brake will be applied and can be overheated and destroyed by the motor continuing to rotate. The shortest switching times of the brakes are achieved by DC switching of the voltage. A spark suppressor is required to suppress interference and to increase the service life of the relay contacts here.
Spring-operated holding brakes are available for the asynchronous servo motors MCA20, 22 and 26. The brakes are activated when the supply voltage is disconnected (closed-circuit principle). When using the brakes purely as holding brakes, virtually no wear occurs on the friction surfaces.
The brakes used are not safety brakes in the sense that a reduction in torque may arise as a result of disruptive factors that cannot be influenced, e.g. oil ingress. The ohmic voltage drop along the cable must be taken into consideration in long motor supply cables and must be compensated for by a higher voltage at the line input.
Whether we have MCA asynchronous motor in stock in Boise, Idaho or need to ship direct from Lenze to any USA cities; ACTECHDRIVES.COM can get MCA asynchronous servos to you fast and save you some money. Our industrial factory automation supplies distributors warehouse stocks some Lenze AC Tech products enabling us to further assist you in finding the correct MCA asynchronous servomotor in the USA, Canada, or Mexico. It will be very helpful if you have the MCA asynchronous servo motor part numbers ready, then our sales representatives can provide you with a pricing and availability quote for MCS asynchronous servo motors that you are looking for in seconds. If you do not have the part numbers for MCA asynchronous servomotors, our application engineers will be able to help you figure out the part numbers and get the price quote to you as soon as possible.
With Suitably Adapted Friction Linings, spring applied brakes can not only fulfil the purely static holding function, they can also be used a working brake for highly dynamic emergency stops. This feature means that the springapplied brake is predestined for use in many servo applications, such as in material handling or in wind power. In a power cut, for example, it is extremely important that a servo brake can be applied from
AC Tech Drives
From Harsh Environments to high torque loads, the M1000 Series microdrives meet the toughest requirements with outstanding reliability, at a low cost. The easy-to-program AC Tech M1000 offers full features, extensive I/O, and a full array of programmable functions. The M1000 is available in a power range of 1/4 to 150 HP (0.18 - 110 kW) and voltages ranging from 115 to 575 VAC. With its Enhanced Torque System (ETS),